#include "app_config.h"

#include "system/includes.h"
#include "device/includes.h"
#include "asm/includes.h"
#include "wifi/wifi_connect.h"
#include "asm/spi.h"
#include "server/audio_dev.h"

/* Wi-Fi RF 校准参数 */
const struct wifi_calibration_param wifi_calibration_param = {
    .xosc_l = 0x0b,
    .xosc_r = 0x0b,

    .pa_trim_data = {1, 7, 4, 7, 11, 1, 7},

    .mcs_dgain = {50,50,50,50,72,72,85,80,64,64,62,52,72,90,80,64,64,64,50,43}
};


//灯带配置
PWM_PLATFORM_DATA_BEGIN(lamp_warm_pwm_data)/* PC1：暖光 */
    .port      = IO_PORTC_01,
    .pwm_ch    = PWM_TIMER2_OPCH2,
    .freq      = 5000,
    .duty      = 100,
    .point_bit = 1,
PWM_PLATFORM_DATA_END()

PWM_PLATFORM_DATA_BEGIN(lamp_cool_pwm_data)/* PC2：冷光 */
    .port      = IO_PORTC_02,
    .pwm_ch    = PWM_TIMER3_OPCH3,
    .freq      = 5000,
    .duty      = 50,
    .point_bit = 1,
PWM_PLATFORM_DATA_END()


//显示器配置
SPI2_PLATFORM_DATA_BEGIN(spi2_data)
    .clk  = 1000000,
    .mode = SPI_1WIRE_MODE,
    .port = 'C',
    .attr = SPI_SCLK_L_UPL_SMPH | SPI_UNIDIR_MODE,
SPI2_PLATFORM_DATA_END()


/* debug串口配置 */
UART2_PLATFORM_DATA_BEGIN(uart2_data)
	.baudrate = 1000000,
	.port = PORT_REMAP,
	.output_channel = OUTPUT_CHANNEL0,
	.tx_pin = IO_PORTA_10,
	.rx_pin = -1,
	.max_continue_recv_cnt = 1024,
	.idle_sys_clk_cnt = 500000,
	.clk_src = PLL_48M,
	.flags = UART_DEBUG,
UART2_PLATFORM_DATA_END();

/* 音频配置 MIC1(PH8=+ / PH9=-) 差分接法, 功放 NS4150B(SD脚->PA0) */
static const struct dac_platform_data dac_data = {
    .pa_auto_mute = 0,              /* 测试中由 audio_test 直接控制功放SD脚(PA0), 关掉SDK自动静音 */
    .pa_mute_port = 0xff,           /* 不使用SDK静音机制 */
    .pa_mute_value = 0,
    .differ_output = 0,             /* 单端输出 */
    .hw_channel = 0x03,             /* BIT(0)=DACL | BIT(1)=DACR 双通道都开, 兼容功放接任意一路 */
    .ch_num = 2,                    /* 数字通道数(与回放双声道对应) */
    .vcm_init_delay_ms = 1000,
};

//设备注册
REGISTER_DEVICES(device_table) = {
	{"uart2", &uart_dev_ops, (void *)&uart2_data },
	{"rtc", &rtc_dev_ops, NULL},
    {"spi2", &spi_dev_ops, (void *)&spi2_data },
    //{"audio", &audio_dev_ops, (void *)&audio_data },
    {"lamp_warm_pwm",&pwm_dev_ops,(void *)&lamp_warm_pwm_data},//warm
    {"lamp_cool_pwm",&pwm_dev_ops,(void *)&lamp_cool_pwm_data},//cool
};

static const struct adc_platform_data adc_data = {
    .mic_channel = LADC_CH_MIC1_P_N, /* MIC1 差分: PH8=正 PH9=负 */
    .linein_channel = 0,
    .mic_ch_num = 1,
    .linein_ch_num = 0,
    .all_channel_open = 1,
    .isel = 2,
    .dump_num = 320,
};

static const struct audio_pf_data audio_pf_d = {
    .adc_pf_data = &adc_data,
    .dac_pf_data = &dac_data,
};

static const struct audio_platform_data audio_data = {
    .private_data = (void *)&audio_pf_d,
};

/* 电源配置 */
static const struct low_power_param power_param = {
    .config         = TCFG_LOWPOWER_LOWPOWER_SEL,          //系统休眠
    .btosc_disable  = TCFG_LOWPOWER_BTOSC_DISABLE,         //进入低功耗时BTOSC是否保持
    .vddiom_lev     = TCFG_LOWPOWER_VDDIOM_LEVEL,          //强VDDIO等级,可选：2.8V  2.9V  3.0V  3.1V  3.2V  3.3V  3.4V  3.5V
    .vddiow_lev     = TCFG_LOWPOWER_VDDIOW_LEVEL,          //弱VDDIO等级,可选：2.1V  2.4V  2.8V  3.2V
	.vdc14_dcdc 	= TRUE,	   							   //打开内部1.4VDCDC，关闭则用外部
    .vdc14_lev		= VDC14_VOL_SEL_LEVEL, 				   //VDD1.4V配置
	.sysvdd_lev		= SYSVDD_VOL_SEL_LEVEL,				   //内核、sdram电压配置
	.vlvd_enable	= TRUE,                                //TRUE电压复位使能
	.vlvd_value		= VLVD_SEL_25V,                        //低电压复位电压值
};

/* 复位配置 */
#define LONG_PRESS_RESET_IO    IO_PORTB_01

static const struct long_press lpres_port = {
    .enable   = TRUE,
    .use_sec4 = TRUE,
    .edge     = FALLING_EDGE,
    .iomap    = LONG_PRESS_RESET_IO,
};

/* 官方示例中的保留唤醒参数。*/
static const struct sub_wakeup sub_wkup = {
    .attribute = BLUETOOTH_RESUME,
};

static const struct charge_wakeup charge_wkup = {
    .attribute = BLUETOOTH_RESUME,
};

/* 唤醒/长按复位参数 */
static const struct wakeup_param wk_param = {
    .port[0] = NULL,
    .sub     = &sub_wkup,
    .charge  = &charge_wkup,
    .lpres   = &lpres_port,
};


#ifdef CONFIG_DEBUG_ENABLE
void debug_uart_init()
{
    uart_init(&uart2_data);
}
#endif

void board_early_init()
{
    dac_early_init(0, dac_data.differ_output ? (dac_data.ch_num > 1 ? 0xf : 0x3) : dac_data.hw_channel, 1000);
    devices_init();
}

static void board_power_init(void)
{

    power_init(&power_param);	 //电源模块初始化
	power_wakeup_init(&wk_param);//复位模块初始化
}

void board_init()
{
	board_power_init();
}